G SCREW MUD PUMP

The pump has few parts, compact structure, small volume and simple maintenance

Category

INTRODUCTION

OF G-TYPE SCREW MUD PUMP

G series single-screw pump and G-type screw mud pump are new types of pumps that work according to the principle of oscillating meshing volume. The main working parts are eccentric screw (rotor) and fixed bushing (stator).

Due to the special geometry of the rotor and stator, a separate sealed cavity is formed, the medium is uniformly flowed from the axial direction, the internal flow velocity is low, the volume remains unchanged, and the pressure is stable, so that eddy current and agitation are not generated.

SIMPLE
STRUCTURE EASY TO ASSEMBLE
AND DISASSEMBLE ROTOR
STATOR

The output pressure of each pump is 0.6MPa, the head is 60m (clean water), and it is suitable for conveying medium temperature below 80 °C (special requirements up to 150 °C).

Because the stator is made of a variety of elastic materials, the pump's transport of high-viscosity fluids and the transport of hard suspended particulate media or fiber-containing media are not suitable for general pumping. The flow rate is proportional to the speed.The transmission can be directly driven by a coupling, or by a speed-regulating motor, a V-belt, a gearbox, etc.

FEW PARTS
COMPACT STRUCTURE
SMALL VOLUME
SIMPLE MAINTENANCE

APPLICATION INDUSTRY

OF G-TYPE SCREW MUD PUMP

G type screw pump is a kind of internal meshing closed screw pump, which belongs to the rotor type volume pump.

Because this pump has strong adaptability to the medium, stable flow, good suction performance and small pressure pulsation,in addition to conveying all kinds of fluid media, it can also transport high viscous medium, medium containing hard suspended particles or solid particles, medium containing fibers,good adjustment performance, wide range, high efficiency.

therefore, in environmental protection, shipping, oil, medicine, daily chemical, food, brewing, construction, mining, chemical, printing, paper, power plants, boilers and other industries to be widely used.

PRODUCT FEATURES

OF G-TYPE SCREW MUD PUMP

small parts, compact structure, small size, simple maintenance, rotor and stator are the wearing parts of single-screw pump, simple structure, easy to assemble and disassemble.

It is a new type of pump that works according to the principle of twisting and meshing volume.

The main working components of the G-type screw mud pump are the eccentric screw (rotor) and the fixed bushing (stator).

Use non-toxic and tasteless edible rubber, the working temperature can reach 120 degrees Celsius, if you use high temperature 120 degrees Celsius - 350 degrees Celsius, you can contact this unit.

Due to the special geometrical beginnings of the two parts, separate sealing chambers are formed. The medium is uniformly propelled by the axial flow.

Use non-toxic and tasteless edible rubber, the working temperature can reach 120 degrees Celsius, if you use high temperature 120 degrees Celsius - 350 degrees Celsius, you can contact this unit.

The output pressure of each pump is 0.6MPa-1.2MPa, and the lift is 60m-120m (clear water).

APPLICATION INDUSTRY

OF G-TYPE SCREW MUD PUMP

Compared with the centrifugal pump, the single screw pump does not need to install the valve, and the flow is a stable linear flow.
Compared with the pneumatic diaphragm pump, the single-screw pump can transport various mixed impurities containing gas and solid particles or fibers, and can also transport various corrosive substances.
Compared with gear pumps, single screw pumps can deliver high viscosity materials.
Unlike the plunger pump, diaphragm pump and gear pump, the screw pump can be used for filling and metering of medicaments.

Strong self-suction Pressure stability High head Large flow Low mute Imported rubber wear-resistant stator All copper motor Can transport large diameter particles

PARAMETER AND STRUCTURE

OF G-TYPE SCREW MUD PUMP

Flow rate	0-150 m3/h
Power	0.75-37kw
Caliber	20-135MM

Flow rate	0-150 m3/h
Power	0.75-37kw
Caliber	20-135MM

1	2	3	4	5	6	7	8
Discharge Body	Draw Rod	stator	screw shaft	universal joint or Pin	feed body	connecting Shaft	packing seat

due to the production batch, specific models, the above picture is for reference only,
details can contact our sales staff for specific verification

SHANDONG CHINA COAL INDUSTRIAL & MINING SUPPLIES GROUP CO.,LTD WHY CHOOSE US CREDIBILITY IS LIFE, QUALITY OF SURVIVAL

Shandong China Coal Industrial & Mining Supplies Group Co.,Ltd (hereinafter referred to as China Coal) is a group company, which is a collection of e-commerce, machinery manufacturing, software, research and development, modern logistics of large diversified industrial group. The group has 100 million yuan registered capital , with more than 1100 employees.

China Coal is a professional manufacturing base of mines support equipment, transport equipment, lifting equipment, spray equipment, drilling equipment, ventilation equipment, lifting equipment and other products, as well as research and development new product and mine construction products with advanced high technology.

THE REAL
MANUFACTURER strong technical force.

Product Feedback

Average Star Rating:

History Feedback: (0)

Latest Feedback

　First Pre 1 Next Last

Star Rating:

Contact*

Email or sales@chinacoalintl.com*

Country *

Tel/Wechat/Whatsapp or +86-18660761303 *

Message*

Verification code: Click to replace the verification code.

Refresh

G SCREW MUD PUMP

Menu

Product Feedback

Latest Feedback