Navigation

sail Online
Visited by mobile
back top
menu

Bottom Dumping Mine Car

Used in surface and underground mining of metal mine or other mine, to transport the ore, waste rocks and other materials along the underground tunnels and the surface working site.

Category

Menu

weixin

Bottom Dumping Mine Car Application, Features

Widely used for surface and underground mining of metal mine or other mine

To transport the ore, waste rocks and other materials in the process of mining

Running smoothly on curve or straight rail.

Adpoted welding structure, withstand the traction, enhence service life.

Made by high quality steel. Technical conditions executes JB/T6992-1993.

Mass and section thickness optimized

Our bottom dumping mine car has safety certificate of approval for mining products.

Bottom Dumping Mine Car Model

Bottom Dumping Mine Car Bottom Dumping Mine Car

Bottom Dumping Mine Car Parameters

Model

Volume

Loading
t

Rated
Loading
t

Gauge
mm

Overall Dia

Wheel
base
mm

Wheel
Dia
mm

Tracktion
Height
mm

Rated
Tracktion
KN

Unloading
Angle
°

Weight
kg

Thikness
mm

Min
Curve
Radius
m

L
mm

W
mm

H
mm

MDC-3.3/6

3.3 m³

3

5.3

600

3450

1200

1380

1100

350

320

60

50°

1687

5

15

H and Tracktion Height h measured since railway surface. Loading Capacity measursed according to material bulk density ρ=900 kg/m3.

Bottom Dumping Mine Car Principle

Bottom Dumping Mine Car

A transportation tool for moving coal, ore, waste rock and material in the process of mining, dragged by a locomotive or winch.

Bottom Dumping Mine Car

Bottom Dumping Mine Car Structure

Bottom Dumping Mine Car Structure

Mainly consits of carriage, frame, buffer device, open-wheel set, connection device, bottom dumping menchanism, etc.

Carriage:Mechanical and physical properties of the material is not less than Q235-A steel. Technical conditions are in accordance with the provisions of the JB/T6992-1993.
Steel Material before welding should be straight, surface flatness shall not exceed 3 ‰, but the maximum must not exceed 6mm.


Metal structure frame, which can withstand the traction. Welded by channel steel, shaft card. Technical conditions are in accordance with the provisions of the JB/T6992-1993.
Frame sides parallel degree of tolerance for the length of 2 ‰.The flatness tolerance of the flame is 2 ‰ to the frame length (buffer not included ), but the max flatness tolerance should less than 5 mm.
The center plane of the frame traction device should be symmetry to the longitudinal center plane of the frame, and its symmetry tolerance should not exceed 6mm.

Wheel Set
Open-wheel Set: wheel, axle , axile bearung. Technical conditions execute JB/T6992-1993.
Before wheel set assembly ,should clean the iron filings and blockage and cleaning all parts; during bearing assembly, should adopt no shock load method; After loading bearing, wheel rotation should be flexibility.

Buffer Device
Bumper technical conditions in accordance with JB/T6992-1993 Buffer has enough strength, cushioning material toughness value of not less than 30J/cm2,cast steel bumpers there shall be no crack, on the surface of cast steel bumper bolt hole.

Connection Device
Connection device is composed of connection three-ring chain, bolt. Connection three-ring chain conforms with the standard requirements of" MT 244.1 - 2005 coal mine narrow gauge vehicle fittings connection chain ".

Assemble Requirements
Before assembling,all the parts should be inspection qualified.
All parts should be clean, and assembly in a clean environment.
Assembled dimension deviation: the total width of mine material car and the high traction deviation of ± 3 mm, total high deviation of ± 8 mm, length deviation of ± 10 mm.
Deviation of the length of the material mine car of - 10 ~ 0 mm, width deviation of plus or minus 3 mm.
Assembled mine material car should be placed in a special flat road inspection,and a larger than 2mm gap on the surface of the wheel and rail is not allowed.

Bottom Dumping Mine Car

Bottom Dumping Mine Car Installation and Commissioning

bottome dumping mine car

Preparation

Before assembling,all the parts should be inspection qualified.
All parts should be clean, and assembly in a clean environment.
Assembled dimension deviation: the total width of mine material car and the high traction deviation of ± 3 mm, total high deviation of ± 8 mm, length deviation of ± 10 mm. Deviation of the length of - 10 ~ 0 mm, width deviation of plus or minus 3 mm.

Installation

Make sure wheel set center line coincides with the centerline of the track.

Commissioning

Observe whether the wheels rub on the track,handle it in time to prevent damage once the phenomenon occurs.
Observe whether tilt,out of orbit or overturned after it sliding along the slope curve and colliding with another car.
Observe the runing codition on the minimum radius of curvature of the track.

Bottom Dumping Mine Car

Bottom Dumping Mine Car MA

Bottom Dumping Mine Car MA Bottom Dumping Mine Car MA

Product Feedback

Average Star Rating:

History Feedback: (10)

Latest Feedback

  • Contacts:J***y E-mail:J***y @z**i.pk
    Commend: Could you send me product catalogs with more details for reference?
    Customer Services: Dear Customer, We just got your message. Our sales will contact you asap.
  • Contacts:T***a E-mail:T***a @m***d.com
    Commend: Looking forward to your quick reply
    Customer Services: Thank you for your inquire. Our professional sales manager will contact you asap
  • Contacts:B***t E-mail:B***tbr
    Commend: i would like to order this, please help me know the cost of this Drop-bottom Mining Wagon Car.
    Customer Services: Thanks for your support to us! And our sales will contact you soon!
 1 2 3 4 Next Last
Star Rating:
Click to replace the verification code. Refresh
skype sail Online Email:sales@chinacoalintl.com
menu
Home Products Top

+

+

Please leave a message

Related Products